Dataset requirements for shear probes: Difference between revisions
No edit summary |
|||
| (15 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
This page provides an overview of the NetCDF format of benchmark dataset for instruments that measure microstructure shear using airfoil probes. The data format recommended is summarized in [[Netcdf dimensions (shear probes)|standard dimensions]] and | This page provides an overview of the NetCDF format of benchmark dataset for instruments that measure microstructure shear using airfoil probes. The data format recommended is summarized in [[#Shear probe measurements: Data Format|Data Format]] below. | ||
<br> | |||
Please use the following naming convention for [[Netcdf dimensions (shear probes)|standard dimensions]] and include the necessary [[Netcdf meta data (shear probes)|meta data]]. | |||
* [[Netcdf meta data (shear probes)|list of meta data]] | |||
* [[Netcdf dimensions (shear probes)|list of dimension names]] | |||
* [[Quality_control_coding|quality control coding for dissipation estimates]] | |||
ATOMIX provides several [[Tentative benchmarks for shear probes|benchmark data sets]] following these guidelines. | |||
= Minimum and desirable data set = | |||
<div class="mw-collapsible" id="dataset" data-collapsetext="Collapse" data-expandtext="Expand"> | |||
* The absolute minimum signals and information required to estimate the rate of dissipation of kinetic energy consists of: | * The absolute minimum signals and information required to estimate the rate of dissipation of kinetic energy consists of: | ||
| Line 8: | Line 20: | ||
:* a means to estimate the temperature of the fluid so that you can determine its kinematic viscosity. | :* a means to estimate the temperature of the fluid so that you can determine its kinematic viscosity. | ||
The sampling rate of the shear-probe signal should exceed significantly (by a factor of 2 to 4) the value of 150U, where | In addition, it is highly recommended to have a minimum one vibration sensor or accelerometer that can be used to check and eventually correct for platform vibrations. The sampling rate of the shear-probe signal should exceed significantly (by a factor of 2 to 4) the value of 150U, where | ||
U is the speed of the flow past the shear-probe. This speed is often called the speed of profiling, even when the probe is fixed in space and the current causes fluid to flow past the shear probe. The value of 150 cpm equals the spatial resolution of the commonly used shear probe. | U is the speed of the flow past the shear-probe. This speed is often called the speed of profiling, even when the probe is fixed in space and the current causes fluid to flow past the shear probe. The value of 150 cpm equals the spatial resolution of the commonly used shear probe. | ||
| Line 24: | Line 36: | ||
Most commonly available instruments carry two shear probes that are frequently oriented so that they measure orthogonal components of the shear and, thus, provide two independent estimates of the rate of dissipation that you should agree statistically. | Most commonly available instruments carry two shear probes that are frequently oriented so that they measure orthogonal components of the shear and, thus, provide two independent estimates of the rate of dissipation that you should agree statistically. | ||
</div> | |||
= Shear probe measurements: Data Format = | |||
Following the recommendations of the [[Flow chart for shear probes | flow chart]], ATOMIX defined four processing levels a user needs to follow to obtain a standardized estimation of epsilon. The different levels are stored as groups in the NetCDF file, the group names are in brackets: | |||
# [[Level 1 data (shear probes)|Timeseries in physical units (L1_converted)]] | |||
# [[Level 1 data (shear probes)| | |||
#* full resolution data in physical units | #* full resolution data in physical units | ||
# [[Level 2 data (shear probes)|Quality-controlled and segmented timeseries]] | # [[Level 2 data (shear probes)|Quality-controlled and segmented timeseries (L2_cleaned)]] | ||
#* full resolution cleaned and despiked parameters from level 1, subdivided in individual [[Section|sections]]. | #* full resolution cleaned and despiked parameters from level 1, subdivided in individual [[Section|sections]]. | ||
# [[Level 3 data (shear probes)|Spectra]] | # [[Level 3 data (shear probes)|Spectra (L3_spectra)]] | ||
#* raw and cleaned spectra | #* raw and cleaned spectra | ||
# [[Level 4 data (shear probes)|Dissipation <math>\varepsilon</math> estimates]] | # [[Level 4 data (shear probes)|Dissipation <math>\varepsilon</math> estimates (L4_dissipation)]] | ||
#* dissipation estimates and corresponding quality parameter as time series | #* dissipation estimates and corresponding quality parameter as time series | ||
------------------- | ------------------- | ||
return to [[Shear probes]] | return to [[Shear probes]] | ||
[[Category:Shear probes]] | |||
Latest revision as of 15:59, 9 September 2023
This page provides an overview of the NetCDF format of benchmark dataset for instruments that measure microstructure shear using airfoil probes. The data format recommended is summarized in Data Format below.
Please use the following naming convention for standard dimensions and include the necessary meta data.
ATOMIX provides several benchmark data sets following these guidelines.
Minimum and desirable data set
- The absolute minimum signals and information required to estimate the rate of dissipation of kinetic energy consists of:
- a sampled shear-probe signal,
- a means of determining the speed of flow past the shear probe, and
- a means to estimate the temperature of the fluid so that you can determine its kinematic viscosity.
In addition, it is highly recommended to have a minimum one vibration sensor or accelerometer that can be used to check and eventually correct for platform vibrations. The sampling rate of the shear-probe signal should exceed significantly (by a factor of 2 to 4) the value of 150U, where U is the speed of the flow past the shear-probe. This speed is often called the speed of profiling, even when the probe is fixed in space and the current causes fluid to flow past the shear probe. The value of 150 cpm equals the spatial resolution of the commonly used shear probe.
- The desirable data set
A far more desirable, but not absolutely necessary, set of data consists of the following.
- Two or more shear probes for measurement redundancy.
- Vibration sensors or accelerometers that are sensitive to the directions of sensitivity of the shear probes.
- An accurate thermometer.
- A pressure transducer.
- A signal that can be used to estimate the speed of flow past the shear probe.
- Pitch and roll sensors.
Most commonly available instruments carry two shear probes that are frequently oriented so that they measure orthogonal components of the shear and, thus, provide two independent estimates of the rate of dissipation that you should agree statistically.
Shear probe measurements: Data Format
Following the recommendations of the flow chart, ATOMIX defined four processing levels a user needs to follow to obtain a standardized estimation of epsilon. The different levels are stored as groups in the NetCDF file, the group names are in brackets:
- Timeseries in physical units (L1_converted)
- full resolution data in physical units
- Quality-controlled and segmented timeseries (L2_cleaned)
- full resolution cleaned and despiked parameters from level 1, subdivided in individual sections.
- Spectra (L3_spectra)
- raw and cleaned spectra
- Dissipation [math]\displaystyle{ \varepsilon }[/math] estimates (L4_dissipation)
- dissipation estimates and corresponding quality parameter as time series
return to Shear probes
