Most commonly available instruments carry two shear probes that are frequently oriented so that they measure orthogonal components of the shear and, thus, provide two independent estimates of the rate of dissipation that you should agree statistically.
Most commonly available instruments carry two shear probes that are frequently oriented so that they measure orthogonal components of the shear and, thus, provide two independent estimates of the rate of dissipation that you should agree statistically.
</div>
</div>
== Level 1 data (shear probes) ==
== Level 1 data (shear probes) ==
-----------------
-----------------
Line 44:
Line 45:
! Short name
! Short name
! Standard name
! Standard name
! description
|-
|-
| TIME
| TIME
| microstructure sampling rate. Days since 1950-01-01 00:00:00 UTC
| Days since 1950-01-01 00:00:00 UTC
| microstructure sampling rate
|-
|-
| TIME_CTD
| TIME_CTD
| CTD sampling rate. Days since 1950-01-01 00:00:00 UTC
| Days since 1950-01-01 00:00:00 UTC
| CTD sampling rate.
|-
|-
| TIME_VIB
| TIME_VIB
| Vibration sensor sampling rate. Days since 1950-01-01 00:00:00 UTC
| Days since 1950-01-01 00:00:00 UTC
| Vibration sensor sampling rate
|-
|-
| TIME_ACCEL
| TIME_ACCEL
| Accelerometer sampling rate. Days since 1950-01-01 00:00:00 UTC
| Days since 1950-01-01 00:00:00 UTC
| Accelerometer sampling rate.
|-
|-
| TIME_SLOW1
| TIME_SLOW1
| Sampling rate slower than microstructure sampling rate. Days since 1950-01-01 00:00:00 UTC
| Days since 1950-01-01 00:00:00 UTC
| Sampling rate slower than microstructure sampling rate.
|-
|-
|N_SHEAR_SENSORS
|N_SHEAR_SENSORS
Line 99:
Line 106:
</div>
</div>
------
------
return to [[Dataset requirements for shear probes]].
return to [[Dataset requirements for shear probes]].
The absolute minimum signals and information required to estimate the rate of dissipation of kinetic energy consists of:
a sampled shear-probe signal,
a means of determining the speed of flow past the shear probe, and
a means to estimate the temperature of the fluid so that you can determine its kinematic viscosity.
The sampling rate of the shear-probe signal should exceed significantly (by a factor of 2 to 4) the value of 150U, where
U is the speed of the flow past the shear-probe. This speed is often called the speed of profiling, even when the probe is fixed in space and the current causes fluid to flow past the shear probe. The value of 150 cpm equals the spatial resolution of the commonly used shear probe.
The desirable data set
A far more desirable, but not absolutely necessary, set of data consists of the following.
Two or more shear probes for measurement redundancy.
Vibration sensors or accelerometers that are sensitive to the directions of sensitivity of the shear probes.
An accurate thermometer.
A pressure transducer.
A signal that can be used to estimate the speed of flow past the shear probe.
Pitch and roll sensors.
Most commonly available instruments carry two shear probes that are frequently oriented so that they measure orthogonal components of the shear and, thus, provide two independent estimates of the rate of dissipation that you should agree statistically.
Level 1 data (shear probes)
TO DO:
Fit the parameter names and definitions to the NetCDF parameter attributes
Level 1 data refers to the full resolution data in physical units, e.g. the regularly sampled time series of converted shear probe data. If needed, a transfer function for shear is given. Below, a table with parameters included in the level 1 data set is compiled.
Dimensions
Example of collapsible table
Short name
Standard name
description
TIME
Days since 1950-01-01 00:00:00 UTC
microstructure sampling rate
TIME_CTD
Days since 1950-01-01 00:00:00 UTC
CTD sampling rate.
TIME_VIB
Days since 1950-01-01 00:00:00 UTC
Vibration sensor sampling rate
TIME_ACCEL
Days since 1950-01-01 00:00:00 UTC
Accelerometer sampling rate.
TIME_SLOW1
Days since 1950-01-01 00:00:00 UTC
Sampling rate slower than microstructure sampling rate.
